Skip to content
TOPOLUMA

How to 3D print a terrain model from real elevation data (STL)

Turn any site or mountain into a printable STL: choosing the print size, base thickness and vertical exaggeration, plus slicer settings for a clean terrain print.

Updated · 8 min read

A printed terrain model explains a site faster than any drawing: where the ground rises, where the valley runs, how a building would sit on the slope. This guide goes from a place on the map to an STL that slices without repairs, and explains the three numbers that decide whether the print looks right: the print size, the base and the vertical exaggeration.

The workflow in TOPOLUMA

  1. Choose the area. In the studio, search the place and draw a rectangle. The model is scaled by its longest side, so a square area uses a square print bed best.
  2. Set the terrain. In Layers → 3D terrain surface, choose the mesh resolution (2 m to 50 m), the vertical exaggeration (1× to 5×) and the Solid base (STL), the thickness below the lowest point of the terrain, in real-world metres.
  3. Decide on buildings and trees. Buildings are extruded OpenStreetMap footprints; trees are small low-poly shapes. Both print well only at large scales (see below), so turn them off for a landscape model.
  4. Generate the preview and look at the site in 3D view.
  5. Export. In Export, tick STL and set Print size (STL): the length of the longest side of the printed model in millimetres (20 to 2,000 mm). Leave it empty for a model at real size in metres. The download is a binary STL; the README states the units and the print size.

Work out the scale first

Everything else follows from the scale of the print: the print size divided by the real length of the longest side.

  • An area 3 km wide printed at 150 mm is at 1:20,000: 1 mm on the print is 20 m on the ground.
  • An area 600 m wide printed at 200 mm is at 1:3,000: 1 mm is 3 m.

The base thickness is entered in real metres because it belongs to the terrain, not to the printer. To get a base of a given printed thickness, multiply by the scale: base in metres = printed base in mm × scale ÷ 1,000. At 1:20,000, a 3 mm base needs 60 m; at 1:3,000 it needs 9 m. The default of 10 m is fine for small sites and too thin for large areas.

Vertical exaggeration

At small scales, real relief prints flatter than people expect. A hill rising 100 m is 5 mm tall at 1:20,000, which reads as texture rather than a hill. Exaggeration multiplies every height in the model to make the relief readable. As a starting point:

TerrainStarting exaggeration
High mountains (relief over 1,000 m in the area)1× to 1.5×
Hills and valleys1.5× to 2×
Gentle or flat land2× to 3×, more for very flat sites

Say on the model or its label that the heights are exaggerated, and by how much. For a model used to judge slopes or views, keep it at 1×.

Mesh resolution and detail

The detail in a print is limited by three things: the elevation data, the mesh and the printer. In most of the world the data is Copernicus GLO-30, one height every 30 m; in countries with open lidar it can be 1 m or finer. A 0.4 mm nozzle draws features down to roughly half a millimetre.

  • At 1:20,000, one 30 m data cell is 1.5 mm on the print, so the data, not the printer, limits the detail. A 10 m or 20 m mesh is enough.
  • At 1:3,000, one 30 m cell is 10 mm: the surface will look smooth and rounded. A finer mesh makes it smoother, not more detailed. Where lidar data exists, a 2 m or 5 m mesh shows real detail at this scale.
  • For large areas the mesh is coarsened automatically so the file stays workable.

Buildings and trees

A 10 m building is 0.5 mm on a 1:20,000 print, below what most printers show cleanly, and trees are smaller still. Buildings start to read at around 1:5,000 and larger (towns and neighbourhoods), and become the point of the model at 1:1,000 to 1:2,000. Heights come from OpenStreetMap where they are mapped and from your default height elsewhere, so check the buildings that matter. The STL keeps buildings and trees as separate closed bodies standing on the terrain; most slicers merge them when slicing, and their repair function fixes the rest.

Slicer settings that work for terrain

  • Units: a scaled STL is in millimetres, so it should import at the print size you set. An unscaled one is in metres and will look enormous.
  • Orientation: print flat on the base. Terrain has no overhangs, so supports are rarely needed.
  • Layer height: 0.1 to 0.15 mm makes the terracing of gentle slopes much less visible than 0.2 mm or more, at the cost of print time.
  • Infill: a terrain model is mostly solid volume, so 10% to 15% infill is enough and saves material. Use enough top layers to close the surface.
  • Contour bands: a filament change or a pause at chosen heights gives coloured height bands, like a printed hypsometric map. The layer height in the slicer tells you which layer matches which elevation.

Limits

The model follows the elevation data, so it shows the shape of the land, not small features. Copernicus GLO-30 is a surface model: forests and dense cities can print as raised patches. The guide to free elevation data explains the difference between surface and terrain models, and which data is used where.